모델명 : ETCR1000C

원산지 : CHINA

브랜드 : ETCR

Ⅰ. Introduction

Safe and Time Saving

Traditional phase sequence measurement methods must poke the three-phase wire terminal, 

and connect the three bare alligator clips or test pins of phase sequence meters to the three bare firing lines, 

while ETCR1000C uses clamp non-contact measurement, without taking off the wire and no need to contact high-voltage bare fire-wire, 

the test can be made by directly clamping the three-phase insulating sheath by three super-sensitive high-insulated clamps. 

Conducting measurement on sheathed cable significantly improves the safety of field testing, effectively protect the operator’s personal safety and increase productivity!

Convenient Operation

Instrument base plate is provided with magnet, instrument can adsorbed on the metal shell when testing, the operation more convenient.

Multi-Purpose

In addition to phase sequence detection, it also has the functions of live wire examination, simple power detection, fire-wire identification, phase deficiency determination, break location detection, DC line break and line maintenance, equivalent to 3 induction electric pens.  

Dynamic Display

LED dynamic display, intuitive and clear

Sensitive and reliable

More sensitive ETCR1000C clamp, can even sense the AC voltage signal as low as a few Volts, with a wider range of live electricity.

Beautiful and scientific

The three clamps of ETCR1000C are in three colors, Red, Yellow and Green; It is more in line with the distinction of three-phase line, and more scientific and artistic overall appearance.

Ultra-low Power Consumption

ETCR1000C has a better power-saving performance with the maximum rated power of 100mVA.

Ⅱ. Technical Specifications

Functions

Phase detection (normal phase, reverse phase and phase deficiency), Live wire examination, Simple Power detection, Breakpoint location and Line maintenance.  

Power Supply

DC3V AA Mn batteries (R6P) ×2 PCS, Continuously working for 200 hours

AC Voltage Range(V)

AC0～600V, 40～70Hz (Sine Wave Continuous Input)

Clamp Wire Size

Diameter ø1.6-ø16mm

LED Display

【Positive Phase Sequence】

The four phase-sequence lamps blink in order (clockwise).

【Negative Phase Sequence】

The four phase-sequence lamps blink in order (counterclockwise).

【Line-voltage Indication】L1、L2、L3  lamp light up.

【Default Phase】L1/L2/L3  lamp is off.

【Open Circuit】L1/L2/L3  lamp is off.

Power On Indication

Power on indication light turns on

Auto Power off

After 5 minutes, the meter automatically cut off power supply.

Meter Dimension

Width, height, thickness 70mm*75mm*30mm

Clamp Lead Length

0.5m

Meter Weight

180g (with battery)

Working Temperature and Humidity

-10℃～55℃; below 80%rh

Storage Temperature and Humidity

-20℃～60℃; below 90%rh

Maximum Measured Voltage

AC600V

Dielectric Strength

5.4kVrms

Maximum rated Power

100mVA

Safety Provisions

EN61010-1: 2001, EN61010-031: 2002, Pollution level 2, CAT Ⅲ(600V), Transient over-voltage 6000V

Accessories

Meter: 1 Piece; Carrying case; 1 Piece.

-.Function;phase detection(Normal,reverse),live wire examination,simple power inspection,phase deficiency judgement,breakpoints finding and line maintenance,instrument base plate is provided with a magnet,the operation more convient.

-.Display ;LED

-.Power supply; DC3V AA Mn batteries(R6P) x2 PCS

-.Buzzer;yes

-.Line voltage range;AC 60~600V/1000V,40~70Hz(sine wave continuous input)

-.Clamp wire size;pie 1.6~16mm

-.Auto power  off ;3minutes after booting up ,the meter automatically cut off power supply

-.Dimension;70(L)x75(W)x30(H)mm

-.Clamp lead length;0.5m

-.Weight;180gr(with the batteries)

-.Working temperature & humidity;-10~55C,below 80%RH

-.Maximum measured voltage;AC600V/AC1000V

-.Dielectric strength;5.4kVrms

-.Maximum rated power;100mVA

-.Accessories;carrting case x1pc,manual x1pc,